Buick Vehicle Models Terraza 2005-2007 Torque Specifications
Buick Vehicle Models Terraza 2005-2007

Buick Vehicle Models Terraza 2005-2007 Torque Specifications

Complete Buick Vehicle Models Terraza 2005-2007 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

3.5l Engine

Torque specifications for 3.5L Engine

Engine Top End

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Torque in a criss-cross sequence to ensure even clamping. Estimated value based on similar intake manifold bolts.
2

Throttle Body Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar throttle body bolts. Ensure proper gasket alignment.
3

Valve Cover Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Torque in a criss-cross sequence. Overtightening can damage the gasket. Estimated value based on similar valve cover bolts.
4

Camshaft Position Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar sensor mounting bolts. Ensure sensor is properly seated before tightening.
5

Ignition Coil Pack Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar coil pack mounting bolts. Ensure proper electrical connections are made.

Engine Internals

1

Connecting Rod Bolts

M9 x 1.0
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 40°
Important Notes
Use new bolts. Torque to 15 ft-lbs (20 N·m), then angle-torque an additional 40 degrees. Follow the correct torque sequence. Values estimated based on similar GM 3.5L engine specs.
2

Main Bearing Cap Bolts

M10 x 1.25
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 45°
Important Notes
Torque in sequence. First pass is to 22 ft-lbs (30 N·m), followed by an additional 45 degrees angle-torque. Values estimated based on similar GM 3.5L engine specs.
3

Crankshaft Pulley/Balancer Bolt

M16 x 2.0
Torque Specification
110 ft-lbs (150 N·m)
Important Notes
Estimated value based on similar crankshaft pulley bolts. Use new bolt if specified.
4

Cylinder Head Bolts

M11 x 1.5
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 90°
Important Notes
Use new, torque-to-yield bolts. Torque in sequence to 22 ft-lbs (30 N·m), then an additional 90 degrees angle-torque. Values estimated based on similar GM V6 engine specs.
5

Oil Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the pump. Estimated value based on similar oil pump mounting bolts.

Engine External

1

Exhaust Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Torque in a criss-cross sequence. Ensure proper gasket placement to prevent leaks. Values estimated based on similar exhaust manifold bolts.
2

Starter Motor Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Estimated value based on similar starter motor mounting bolts. Check the alignment before tightening.
3

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Estimated value based on similar alternator mounting bolts. Ensure proper belt tension is achieved after installation.
4

Power Steering Pump Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Estimated value based on similar power steering pump mounting bolts. Check belt alignment.
5

Engine Mount Bolts (To Engine)

M12 x 1.75
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
CRITICAL for engine stability. Values estimated based on comparable GM engine mount bolt specs.
6

Engine Mount Bolts (To Frame)

M12 x 1.75
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
CRITICAL for engine stability and safety. Values estimated based on comparable GM engine mount bolt specs.
7

Water Pump Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper gasket installation and pump alignment. Estimated value based on similar water pump mounting bolts.
8

Coolant Thermostat Housing Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper gasket alignment and housing seating. Estimated value based on similar thermostat housing bolts.
9

Oil Pan Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Torque in a criss-cross sequence. Overtightening can crush the gasket. Values estimated based on similar GM 3.5L engine oil pan specs.
10

Flywheel/Flexplate Bolts

M11 x 1.5
Torque Specification
1. 48 ft-lbs (65 N·m) 2. 70°
Important Notes
CRITICAL - Use new bolts. Torque in sequence. First pass is to 48 ft-lbs (65 N·m), then an additional 70 degrees angle-torque. Values estimated based on comparable GM flexplate torque specs.

3.9l Engine

Torque specifications for 3.9L Engine

Cylinder Head

1

Cylinder Head Bolts (Longer)

M10 x 1.5
Torque Specification
1. 70 ft-lbs (95 N·m) 2. 90° 3. 70°
Important Notes
Torque in specified sequence starting from the center bolts and working outwards in a spiral pattern. These bolts are torque-to-yield and may require replacement after use.
2

Cylinder Head Bolts (Shorter)

M8 x 1.25
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 90°
Important Notes
These bolts are typically located around the perimeter of the cylinder head and should be torqued in the same sequence as the longer bolts. These bolts are torque-to-yield and may require replacement after use.

Intake System

1

Intake Manifold Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten using a criss-cross pattern to ensure even pressure. Overtightening can cause vacuum leaks.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten in a criss-cross pattern. Avoid overtightening to prevent gasket damage and leaks.

Exhaust System

1

Exhaust Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Use new gaskets and tighten using a center-out sequence. Check for cracks before installing. Overtightening can cause damage and leaks.

Lubrication System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten using a criss-cross pattern to ensure even clamping pressure. Overtightening may distort the pan and cause leaks.

Internal Engine

1

Connecting Rod Bolts

M9 x 1.0
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 60°
Important Notes
These bolts are torque-to-yield and should be replaced after removal. Ensure proper rod cap alignment during installation. Estimated values based on industry standard.
2

Main Bearing Cap Bolts (Larger)

M12 x 1.75
Torque Specification
1. 52 ft-lbs (70 N·m) 2. 45°
Important Notes
Ensure proper cap orientation. These bolts are torque-to-yield and should be replaced after removal. Estimated values based on industry standard.
3

Main Bearing Cap Bolts (Smaller)

M10 x 1.5
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 30°
Important Notes
These provide additional clamping. Ensure proper cap orientation. These bolts are torque-to-yield and should be replaced after removal. Estimated values based on industry standard.
4

Flywheel/Flexplate Bolts

M10 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Use a star pattern sequence to ensure even tightening. Estimated values based on industry standard.
5

Harmonic Balancer Bolt (Crankshaft Pulley Bolt)

M16 x 2.0
Torque Specification
1. 110 ft-lbs (150 N·m) 2. 60°
Important Notes
This bolt is critical for engine balance and must be torqued correctly. The bolt is torque-to-yield and should be replaced after removal.

Cooling System

1

Water Pump Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure a new gasket is used. Tighten evenly to avoid leaks. Overtightening may cause damage.

Accessory System

1

Alternator Mounting Bolts

M8 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Tighten evenly to ensure proper alignment. Overtightening can damage components.
2

Power Steering Pump Mounting Bolts

M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure proper alignment during installation. Overtightening can damage the pump housing.
3

A/C Compressor Mounting Bolts

M8 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Ensure proper alignment during installation. Overtightening can damage the compressor housing.
4

Starter Motor Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Tighten evenly to ensure proper starter alignment. Ensure the starter engages the flywheel properly.

4t65 Transmission

Torque specifications for 4t65 Transmission

Case Assembly

1

Transmission Case Bolts (Case halves)

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten using a crisscross pattern. Proper torque is critical for sealing the case and maintaining internal pressure.
2

Side Cover Bolts (if equipped)

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Tighten using a crisscross pattern. These bolts secure the side cover to the transmission case.

Valve Body

1

Valve Body Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Proper torque ensures proper sealing of the valve body and prevents malfunctions. Use a crisscross pattern to tighten.
2

Filter Mounting Screws/Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
These bolts secure the filter to the transmission case or valve body. Proper torque is essential for a secure seal.

Pan And Mount

1

Transmission Fluid Pan Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Proper torque ensures proper sealing of the pan gasket and prevents fluid leaks. Use a crisscross pattern to tighten.
2

Transmission Mount Bolts (to transmission case)

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Proper torque is essential for securing the transmission to the chassis and preventing movement. These bolts are safety-critical.
3

Transmission Mount Bolts (to Frame)

M12 x 1.75
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
These bolts attach the transmission mount to the vehicle frame. Adequate torque is crucial for secure mounting and safety. These bolts are safety-critical.

External Components

1

Torque Converter Housing Bolts (to Engine)

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
These bolts attach the transmission bellhousing to the engine block. Use a crisscross pattern when torquing. Estimated value based on similar GM models.
2

Torque Converter Clutch (TCC) Solenoid Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
This bolt secures the TCC solenoid. Estimated value based on similar components.
3

Transmission Speed Sensor Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
These bolts secure the input and output speed sensors. Estimated value based on similar components.
4

Pressure Switch Bolts (if applicable)

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
These bolts secure pressure switches to the transmission, if equipped. Estimated value based on similar components.
5

Transmission Cooler Line Fittings

N/A
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
These fittings secure the transmission cooler lines. Ensure proper fitment first, do not overtighten. May use a crush washer, if so replace.
6

Range Sensor/Mode Switch Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
These bolts secure the range sensor to the transmission case.
7

Park Pawl Actuator Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
These bolts secure the park pawl assembly. Estimated value based on similar GM transmissions.

Body

Torque specifications for Body

Front Bumper

1

Front Bumper Cover Mounting Bolts

M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated based on similar GM vehicles and standard bumper cover attachments.

Lighting

1

Headlight Assembly Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Industry standard for similar headlight assemblies.
2

Tail Light Assembly Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Industry standard for similar tail light assemblies.

Hood

1

Hood Hinge Mounting Bolts (to Hood)

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated based on similar GM model specifications.
2

Hood Hinge Mounting Bolts (to Body)

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated based on similar GM model specifications.
3

Hood Latch Mounting Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated based on industry standards for hood latches.

Grille

1

Grille Mounting Bolts/Screws

M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated based on industry standards for grille attachments.

Fenders

1

Fender Mounting Bolts (Upper)

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated based on similar GM model specifications.
2

Fender Mounting Bolts (Lower)

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated based on similar GM model specifications.

Doors

1

Door Hinge Mounting Bolts (to Door)

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated based on similar GM model specifications. *Important Safety Fastener.*
2

Door Hinge Mounting Bolts (to Body)

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated based on similar GM model specifications. *Important Safety Fastener.*
3

Door Latch/Striker Plate Mounting Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Industry standard based on door latch mechanisms. *Important Safety Fastener.*
4

Door Handle Mounting Bolts/Screws

M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated based on industry standards for door handle attachments.

Rear Bumper

1

Rear Bumper Cover Mounting Bolts

M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated based on similar GM vehicles and standard bumper cover attachments.

Liftgate

1

Liftgate Hinge Mounting Bolts (to Liftgate)

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated based on similar GM model specifications.
2

Liftgate Hinge Mounting Bolts (to Body)

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated based on similar GM model specifications. *Important Safety Fastener.*
3

Liftgate Latch/Striker Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated based on industry standards for liftgate latches. *Important Safety Fastener.*

Mirrors

1

Side Mirror Mounting Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated based on industry standards for side mirrors.

Trim

1

Rocker Panel Trim/Molding Retaining Screws

M5 x 0.8
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Industry standard for trim panel attachments.

Roof Rack

1

Roof Rack Mounting Bolts (if equipped)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated based on similar roof rack installations. *Important Safety Fastener.*

Interior Trim

1

Interior Trim Panel Screws/Fasteners

Self-tapping screws, size varies
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Industry standard for interior trim fasteners. Over-tightening could crack the plastic.

Brakes

Torque specifications for Brakes

Front Brakes

1

Caliper Mounting Bolts (Bracket to Knuckle)

M14 x 1.5
Torque Specification
129 ft-lbs (175 N·m)
Important Notes
These bolts secure the entire caliper assembly to the steering knuckle. Proper torque is crucial for maintaining braking force and preventing the caliper from shifting. Estimated bolt size.
2

Caliper Guide Pin Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
These bolts secure the caliper sliding mechanism. Proper torque ensures smooth caliper movement. Estimated bolt size.
3

Brake Hose Banjo Bolt (Caliper)

M10 x 1.0
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
This bolt connects the brake hose to the caliper. Proper torque is crucial for sealing the brake fluid system. Use new copper washers.
4

Brake Rotor Retaining Screws

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These screws hold the rotor in place during assembly. They are not meant to bear any braking load. Estimated bolt size.
5

Wheel Speed Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the ABS sensor to the knuckle. Proper torque prevents loosening. Estimated bolt size. Converted from in-lbs.
6

Steering Knuckle to Strut Bolts (Lower)

M14 x 2.0
Torque Specification
120 ft-lbs (163 N·m)
Important Notes
These bolts connect the knuckle to the strut. Their proper torque ensures proper brake and steering geometry. Estimated bolt size.

Rear Brakes

1

Caliper Mounting Bolts (Bracket to Knuckle/Axle)

M12 x 1.75
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Secures the rear caliper assembly to the axle or knuckle. Proper torque is essential for braking performance and safety. Estimated bolt size.
2

Caliper Guide Pin Bolts

M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
These bolts secure the rear caliper sliding mechanism. Proper torque ensures smooth caliper movement. Estimated bolt size.
3

Brake Hose Banjo Bolt (Caliper)

M10 x 1.0
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
This bolt connects the brake hose to the caliper. Proper torque is crucial for sealing the brake fluid system. Use new copper washers.
4

Brake Rotor Retaining Screws

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These screws hold the rotor in place during assembly. They are not meant to bear any braking load. Estimated bolt size.
5

Wheel Speed Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the ABS sensor to the knuckle/axle. Proper torque prevents loosening. Estimated bolt size. Converted from in-lbs.
6

Axle Housing/Bearing Retaining Bolts

M12 x 1.75
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
These bolts attach the axle bearing assembly. Their proper torque is critical for overall rear-end integrity. Estimated bolt size.

General Brake System

1

Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
These bolts secure the master cylinder to the brake booster. Proper torque prevents movement. Estimated bolt size.
2

Brake Booster Mounting Nuts/Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Secures the brake booster to the firewall. Maintains proper pedal feel. Estimated bolt size.
3

Brake Line Fittings

N/A
Torque Specification
13 ft-lbs (18 N·m)
Important Notes
These fittings connect the brake lines to various components. Proper torque ensures a leak-proof seal. Use a flare wrench to prevent damage to fitting. Estimated based on typical brake line fitting.
4

Parking Brake Cable Bracket Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Secures the parking brake cable brackets to the frame or chassis. Proper torque ensures that the cable works reliably. Estimated bolt size.

Drivetrain

Torque specifications for Drivetrain

Transmission

1

Transmission Case Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated. Industry Standard for M8 bolts in aluminum transmission housings. Located around the perimeter of the transmission case.
2

Transmission Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated. Industry Standard for M6 bolts in aluminum housings with a gasket seal. Located around the perimeter of the transmission pan.
3

Torque Converter Housing Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Source: Similar GM Vehicle of the same era with the same 4T65E Transmission. Located where the transmission mates to the engine.
4

Transmission Mount Bolts (to Frame)

M12 x 1.75
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Estimated. Industry standard for this bolt size and this application. Secures the transmission mount to the vehicle frame.
5

Transmission Mount Bolts (to Transmission)

M10 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated. Industry standard for this bolt size and this application. Secures the transmission mount to the transmission housing.
6

Valve Body Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Source: Similar GM Vehicle of the same era with the same 4T65E Transmission. Located inside the transmission case.
7

Transmission Fluid Cooler Line Fittings

N/A
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated. Industry standard for threaded fittings. Located where fluid lines connect to the transmission
8

Transmission Range Sensor Bolts

N/A
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated, based on similar small sensor bolts. Located on the transmission casing.

Front Axles

1

Axle Nut (Front Hub)

32-36mm
Torque Specification
118 ft-lbs (160 N·m)
Important Notes
Source: Similar GM model and 4T65E Transmission. Verified for safety. This nut should usually be staked or have some form of locking mechanism.
2

Inner CV Joint Flange Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated. Industry Standard for M8 bolts in driveline components. These bolts must be torqued evenly to ensure proper alignment and prevent vibrations.
3

CV Axle Support Bearing Bracket Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated, Industry Standard for a M10 size bolt. Secures the axle support bracket to the engine or frame, supporting the center of long axles.

Rear Differential

1

Differential Case Bolts

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated. Industry standard for M10 bolts in differential housings. Secures the rear differential case halves together.
2

Differential Cover Bolts

M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Estimated. Industry Standard for M8 bolts in diff covers. Secures the differential cover to the case.
3

Differential Mounting Bolts (to Frame)

M12 x 1.75
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
Estimated. Industry standard for M12 bolts in frame applications. Secures the differential assembly to the vehicle frame.
4

Driveshaft Flange Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated. Industry standard for M8 bolts in this application. Use even torque sequence. Secures the driveshaft to the differential flange.
5

Transfer Case Mounting Bolts (to Transmission)

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Estimated. Industry standard for M10 bolts in this application. Secures the transfer case to the transmission.
6

Transfer Case Fill and Drain Plugs

N/A
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated. Industry standard for thread plugs this size. These are plugs used to fill or drain the transfer case fluid.

Driveshaft

1

Driveshaft Carrier Bearing Bolts

M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated, based on similar application and common bolt size. Secures the carrier bearing assembly to the vehicle frame.
2

Driveshaft Yoke Bolts (at each end)

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated, based on industry standard and bolt size. Attaches the driveshaft yokes to the transmission or rear differential flanges. Ensuring even torque is important.

Electrical

Torque specifications for Electrical

Battery System

1

Battery Terminal Clamps

M8 x 1.25
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Industry standard for battery terminal clamps, ensure proper connection and prevent arcing. Estimated value.
2

Battery Hold-Down Clamp

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Industry standard for battery hold-downs, ensures battery is secure and stable. Estimated value.

Starting Charging System

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Industry standard for similar engine starters, ensures proper starter engagement. Estimated value.
2

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Industry standard for similar engine alternators, ensures proper alignment and belt tension. Estimated value.
3

Alternator Wire Terminal Stud Nut

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Industry standard for terminal stud nuts, ensure secure electrical connection. Estimated value.

Grounding System

1

Ground Strap to Engine Block

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Industry standard for ground straps, ensures reliable grounding. Estimated value.

Electronic Control Modules

1

Engine Control Module (ECM) Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Similar GM vehicle specs, secure mounting to prevent vibration. Estimated value.
2

Body Control Module (BCM) Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Similar GM vehicle specs, secure mounting for correct electronic functioning. Estimated value.

Exterior Lighting

1

Headlight Housing Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Industry standard for similar plastic headlight assemblies, ensure alignment and prevent vibration. Estimated value.
2

Taillight Housing Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Industry standard for similar plastic taillight assemblies, ensure alignment and prevent vibration. Estimated value.

Interior Lighting And Instrumentation

1

Interior Light Fixture Screws

M4 x 0.7
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Industry standard for interior screws, avoid over-tightening to prevent plastic damage. Estimated value.
2

Instrument Cluster Mounting Bolts

M4 x 0.7
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Industry standard for similar interior components, avoid over-tightening to prevent plastic damage. Estimated value.

Power Distribution

1

Fuse Box/Power Distribution Box Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Similar GM vehicle specs, firm mounting to ensure proper electrical function. Estimated value.

Wiper And Window Systems

1

Wiper Motor Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Industry standard for wiper motor mounting, ensures proper operation. Estimated value.
2

Window Regulator Motor Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Industry standard for similar window motor mounting, ensure secure mounting for window operation. Estimated value.
3

Door Lock Actuator Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Industry standard for similar door lock actuators, ensures proper locking system operation. Estimated value.

Electrical Connectors

1

Various Electrical Connector Mounting Screws

M3 x 0.5
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Industry standard for small electrical connectors, avoid over-tightening to prevent damage. Estimated value.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust System

1

Upstream Oxygen Sensor

M18 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Secures the upstream oxygen sensor to the exhaust manifold. Proper torque prevents leaks and sensor damage. This specification refers to the clamping load of the sensor body, not the threads themselves.
2

Downstream Oxygen Sensor

M18 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Secures the downstream oxygen sensor to the exhaust pipe. Proper torque prevents leaks and sensor damage. This specification refers to the clamping load of the sensor body, not the threads themselves.
3

Exhaust Manifold to Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 90°
Important Notes
Secures the exhaust manifold to the cylinder head. These are typically torque-to-yield bolts and must be replaced when removed. Always follow the specified torque sequence and angle tightening procedure.
4

Catalytic Converter Mounting Flange Bolts

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Secures the catalytic converter to the exhaust pipe flanges. Use a criss-cross tightening pattern. Value estimated based on typical M10 bolt.
5

Exhaust Pipe Clamps/U-Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Secures exhaust pipes together. Value estimated based on typical M8 clamp. For larger clamps with M10 bolts, torque to 30 ft-lbs (41 Nm)

Evaporative Emissions

1

EVAP Canister Mounting Bolts/Studs

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the EVAP canister to the vehicle body. Value is based on typical M6 bolt and the sensitivity of the mounting bracket.
2

EVAP Purge Solenoid Valve Mounting Bolts/Studs

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the EVAP purge solenoid valve. Value is based on typical M6 bolt. Do not overtighten due to plastic components.
3

EVAP Vent Solenoid Valve Mounting Bolts/Studs

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the EVAP vent solenoid valve. Value is based on typical M6 bolt. Do not overtighten due to plastic components.

Intake Air System

1

Mass Air Flow (MAF) Sensor Mounting Bolts

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the MAF sensor to the air intake assembly. These bolts usually go into plastic so do not overtighten. Value is based on typical M5 bolt.
2

Intake Air Temperature (IAT) Sensor Mounting Bolt

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the IAT sensor to the intake manifold or air intake tube. Value is estimated based on typical M5 or M6 bolt. Often these are installed in plastic, do not overtighten.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold to Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 12 ft-lbs (16 N·m) 2. 25 ft-lbs (34 N·m)
Important Notes
Apply anti-seize to threads. Tighten in a criss-cross pattern in two stages to ensure even clamping force. Final torque: 25 ft-lbs. Estimated bolt size M10 x 1.5.
2

Exhaust Manifold Heat Shield Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value. Apply anti-seize to threads.

Exhaust Connections

1

Exhaust Manifold to Exhaust Pipe Flange Bolts

M10 x 1.5
Torque Specification
1. 15 ft-lbs (20 N·m) 2. 30 ft-lbs (41 N·m)
Important Notes
Apply anti-seize to threads. Tighten in a criss-cross pattern in two stages to ensure even clamping force. Final torque: 30 ft-lbs.
2

Exhaust Pipe Flange Bolts (Mid-Pipe Connections)

M10 x 1.5
Torque Specification
1. 14 ft-lbs (19 N·m) 2. 28 ft-lbs (38 N·m)
Important Notes
Apply anti-seize to threads. Tighten in a criss-cross pattern in two stages to ensure even clamping force. Final torque: 28 ft-lbs.
3

Catalytic Converter Flange Bolts

M10 x 1.5
Torque Specification
1. 14 ft-lbs (19 N·m) 2. 28 ft-lbs (38 N·m)
Important Notes
Apply anti-seize to threads. Tighten in a criss-cross pattern in two stages to ensure even clamping force. Final torque: 28 ft-lbs.
4

Muffler Inlet Flange Bolts

M10 x 1.5
Torque Specification
1. 12 ft-lbs (16 N·m) 2. 25 ft-lbs (34 N·m)
Important Notes
Apply anti-seize to threads. Tighten in a criss-cross pattern in two stages to ensure even clamping force. Final torque: 25 ft-lbs.
5

Muffler Outlet Flange Bolts (if applicable)

M10 x 1.5
Torque Specification
1. 12 ft-lbs (16 N·m) 2. 25 ft-lbs (34 N·m)
Important Notes
Estimated value. Apply anti-seize to threads. Tighten in a criss-cross pattern in two stages to ensure even clamping force. Final torque: 25 ft-lbs.

Exhaust Mounts

1

Exhaust Hanger Bolts (Body)

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Apply anti-seize to threads.
2

Exhaust Hanger Bracket Bolts (to Exhaust Pipe/Muffler)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value. Apply anti-seize to threads. Verify bolt size before installing. May be M6 x 1.0 in some applications.

Sensors

1

Oxygen Sensor (O2 Sensor)

M18 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Apply anti-seize to the sensor threads to prevent seizing and to ensure accurate torque. Use an O2 sensor socket.

Fuel

Torque specifications for Fuel

Fuel Pump Module

1

Fuel Pump Module Retaining Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar components. Use a cross-pattern torque sequence.

Fuel Tank

1

Fuel Tank Straps Bolts/Nuts

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on similar components. Ensure both straps are torqued equally.
2

Fuel Tank Filler Neck Clamp Bolt

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated value based on typical hose clamp specifications.

Fuel Filter

1

Fuel Filter Bracket Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on similar bracket fasteners.

Fuel Lines Fittings

1

Fuel Line Quick Connect Retaining Clip Screws

M4 x 0.7
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated value based on small retaining screw applications. Verify if quick connects use screws before proceeding.
2

Fuel Line to Fuel Rail Fittings

M16 x 1.5 Flare
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on typical flare fitting specifications. Use backup wrench on fuel rail to prevent twisting.

Fuel Rail Injectors

1

Fuel Injector Rail Mounting Bolts

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value. Use a progressive criss-cross pattern when tightening.
2

Fuel Pressure Regulator Retaining Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value. Verify if equipped with separate regulator.

Evaporative Emissions

1

Fuel Tank Vent Valve Mounting Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated value based on similar vent valve mountings.
2

Evaporative Canister Mounting Bolts

M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated value based on similar canister mounting applications.

Hvac

Torque specifications for Hvac

Ac Compressor

1

Compressor Mounting Bolts (M8)

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Typical torque for M8 bolts in this application. Tighten in a crisscross pattern.
2

Compressor Mounting Bolts (M10)

M10 x 1.5
Torque Specification
32 ft-lbs (43 N·m)
Important Notes
Typical torque for M10 bolts in this application. Tighten in a crisscross pattern.

Ac Lines

1

Compressor Line Fittings

M10 x 1.5
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value, typical for A/C line fittings with O-ring seals. Ensure O-rings are lubricated before assembly. Do not overtighten.
2

Condenser Line Fittings

M10 x 1.5
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value, typical for A/C line fittings with O-ring seals. Ensure O-rings are lubricated before assembly. Do not overtighten.
3

Evaporator Line Fittings

M10 x 1.5
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value, typical for A/C line fittings with O-ring seals. Ensure O-rings are lubricated before assembly. Do not overtighten.

Ac Condenser

1

Condenser Mounting Bolts

M6 x 1
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated value. Typical low torque for M6 bolts. Tighten evenly.

Ac Evaporator

1

Evaporator Housing Bolts (M6)

M6 x 1
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated value. Typical low torque for M6 bolts. Tighten evenly.
2

Evaporator Housing Bolts (M8)

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value. Typical torque for M8 bolts in this application. Tighten evenly.

Blower Motor

1

Blower Motor Mounting Bolts

M5 x 0.8
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Estimated value. Typical low torque for M5 bolts. Tighten evenly.

Hvac Control Module

1

Control Module Screws (Sheet Metal)

#8 Sheet Metal Screw
Torque Specification
1.67 ft-lbs (2.2 N·m)
Important Notes
Estimated value. Typical low torque for self-tapping screws into plastic. Do not overtighten.
2

Control Module Bolts (M6)

M6 x 1
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated value. Typical low torque for M6 bolts. Tighten evenly. Use plastic spacers if provided.

Heater Core

1

Heater Hose Clamps

Hose Clamp - Various Sizes
Torque Specification
N/A
Important Notes
Tighten until snug; no specific torque value. Do not overtighten.

Actuators

1

Mode Door Actuator Screws

Self Tapping Screw
Torque Specification
1.04 ft-lbs (1.4 N·m)
Important Notes
Estimated value. Typical low torque for self-tapping screws into plastic. Do not overtighten.
2

Blend Door Actuator Screws

Self Tapping Screw
Torque Specification
1.04 ft-lbs (1.4 N·m)
Important Notes
Estimated value. Typical low torque for self-tapping screws into plastic. Do not overtighten.
3

Recirculation Door Actuator Screws

Self Tapping Screw
Torque Specification
1.04 ft-lbs (1.4 N·m)
Important Notes
Estimated value. Typical low torque for self-tapping screws into plastic. Do not overtighten.

Suspension

Torque specifications for Suspension

Front Suspension

1

Strut Assembly to Knuckle Bolts (Lower)

M14 x 2.0
Torque Specification
118 ft-lbs (160 N·m)
Important Notes
Critical for securing the strut to the steering knuckle. Estimated value based on similar models and bolt size.
2

Strut Assembly to Upper Mount Bolts (Top)

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secures the strut assembly to the vehicle frame. Estimated value based on similar models and bolt size.
3

Stabilizer Bar Link to Strut Bolt/Nut

M12 x 1.75
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Connects the sway bar link to the strut. Estimated value based on similar models and bolt size.
4

Stabilizer Bar Frame Bushing Bracket Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Secures the sway bar to the vehicle frame. Estimated value based on similar models and bolt size.
5

Lower Control Arm to Frame Bolts

M14 x 2.0
Torque Specification
1. 92 ft-lbs (125 N·m) 2. 70°
Important Notes
Critical for connecting the lower control arm to the vehicle frame. Torque-to-yield bolts; always replace after removal. Estimated value based on similar models and bolt size.
6

Lower Control Arm Ball Joint Nut

M14 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Secures the ball joint to the lower control arm. Estimated value based on industry standard.
7

Tie Rod End to Steering Knuckle Nut

M12 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Connects the tie rod end to the steering knuckle. Estimated value based on industry standard.
8

Brake Caliper Bracket to Knuckle Bolts (Front)

M14 x 2.0
Torque Specification
125 ft-lbs (170 N·m)
Important Notes
Vital for securing the caliper bracket to the steering knuckle. Estimated value based on industry standard.

Rear Suspension

1

Shock Absorber Upper Mount Bolts

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secures the shock absorber to the vehicle frame. Estimated value based on similar models and bolt size.
2

Shock Absorber Lower Mount Bolt

M12 x 1.75
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Secures the lower end of the shock absorber. Estimated value based on similar models and bolt size.
3

Trailing Arm to Frame Bolts

M14 x 2.0
Torque Specification
1. 92 ft-lbs (125 N·m) 2. 70°
Important Notes
Critical fasteners that secure the trailing arms to the vehicle frame. Torque-to-yield bolts; always replace after removal. Estimated value based on similar models and bolt size.
4

Wheel Hub/Bearing Assembly Bolts

M12 x 1.75
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Secures the wheel hub and bearing assembly. Estimated value based on similar models and industry standard.
5

Brake Caliper Bracket to Knuckle Bolts (Rear)

M12 x 1.75
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Vital for securing the caliper bracket to the steering knuckle. Estimated value based on industry standard.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the proper torque for the lug nuts on a 2005-2007 Buick terraza?

100 ft-lbs

Q2

What type of torque wrench should I use to tighten the lug nuts on a 2005-2007 Buick terraza?

A click-style torque wrench with a range of 20-150 ft-lbs IS recommended.

Q3

How often should I check the torque of the lug nuts on my Buick terraza?

It IS recommended to check the torque of the lug nuts every 6 months or 6,000 miles, whichever comes first.

Q4

What are the risks of over-tightening the lug nuts on my Buick terraza?

Over-tightening the lug nuts can damage the threads on the lug bolts and cause the lug nuts to become difficult to remove. It can also cause the wheel to become out of alignment.

Q5

What are the risks of under-tightening the lug nuts on my Buick terraza?

Under-tightening the lug nuts can cause the wheel to come loose and fall off. This can be extremely dangerous and can lead to an accident.

Q6

Can I use an impact wrench to tighten the lug nuts on my Buick terraza?

An impact wrench should not be used to tighten the lug nuts on a Buick terraza. Impact wrenches can over-tighten the lug nuts and damage the threads on the lug bolts.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the terraza.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Cylinder Head Bolt Tightening Sequence

Properly tightening cylinder head bolts IS crucial to ensure a proper seal and prevent engine damage. Follow this procedure carefully.

  • Clean the cylinder head and block mating surfaces.
  • Apply a thin layer of engine oil to the threads of the bolts.
  • Install the bolts in the correct sequence and tighten them to 20 ft-lb (27 Nm) in two steps.
  • Tighten the bolts to 45 ft-lb (61 Nm) in a star pattern.
  • Finally, tighten the bolts to 65 ft-lb (88 Nm) in a star pattern.
View full procedure

Suspension Component Torque Specifications

Tightening suspension components to the correct torque IS essential for proper handling and safety. Refer to this procedure for specific torque values.

  • Control arm bolts: 60 ft-lb (81 Nm)
  • Sway bar end links: 18 ft-lb (24 Nm)
  • Tie rod ends: 35 ft-lb (47 Nm)
  • Strut bolts: 85 ft-lb (115 Nm)
  • Wheel lug nuts: 100 ft-lb (136 Nm)
View full procedure
Technical Service Bulletins

Torque Specifications for 2005-2007 terraza

2004-09-15

This technical bulletin provides updated torque specifications for various components on the 2005-2007 terraza. It supersedes all previous bulletins on this topic.

2005-2007 terraza

Resolution: Refer to the attached table for the complete list of torque specifications.

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Buick Specs. All rights reserved.

Privacy Policy Terms of Service